How to reset 360 router t2?

Question:How to reset the 360 router t2?

Answer:If you want to reset your 360 router t2, it is recommended to restore it to the factory settings first, and then log in to the ihome.360.cn management page. The setup wizard will automatically appear. Just follow the prompts of the setup wizard and proceed step by step. After completing the settings, you can go online.

Steps:

1. With your 360 router t2 powered on, press and hold theResetPush the button for about 5 seconds to restore your 360 router t2 to factory settings. For more detailed introduction, you can refer to the article:

How to restore the factory settings of 360 router t2?

2. Check whether the network cable connection on your 360 router t2 is correct. The correct connection method between the 360 router t2, optical cat/broadband network cable/wall network port, and computer is as follows:

The WAN port of 360 router t2 should be connected to the LAN port/network port on the optical cat; if optical cat is not used for broadband, you need to directly connect the broadband network cable/wall network port to the home to the WAN port of 360 router t2.

If a computer needs to surf the Internet, use another network cable to connect your computer to any LA port on the 360 router t2.

路由器正确连接示意图

3. On the back of your 360 router t2, check the default WiFi name and management address.

查看登录密码,默认wifi名称

4. Connect your phone to the default wifi viewed in step 3. Only after connecting can your phone set it.

手机连接360家庭防火墙路由器的默认wifi

Note:

(1) After the mobile phone is connected to the default wifi, the mobile phone cannot access the Internet, which is normal. Because when setting up a router with a mobile phone, you don’t need your mobile phone to be in Internet mode. As long as the phone is connected to the router’s wifi network, the phone can set it.

(2) It is recommended to turn off mobile data traffic on mobile phones. If you do not turn off, the mobile phone may not be able to log in to the setting page of the 360 router t2.

5. Type ihome.360.cn in the browser of your mobile phone to open the settings page of the 360 router T2. The page will be prompted to download the 360 Home Firewall APP. Don’t worry about it here. Click “Set up Internet Access” below, as shown in the following figure.

手机设置360家庭防火墙路由器上网1

Note:

If you type ihome.360.cn in your browser, you cannot enter the settings page of the 360 router T2. Please read the following article carefully to see the corresponding solutions.

What should I do if my mobile phone cannot be opened?

6. Click “Set a New Firewall”.

手机设置360家庭防火墙路由器上网2

Note:

If the old router can access the Internet normally, you can click “Transfer Configuration from Old Router”, then connect the WAN ports of the two routers with a network cable, and click the “Start Transfer” button after completing.

7. Next, the router will automatically detect the broadband Internet access method. If it detects “Broadband PPPoE”, then you need to fill in the broadband account number and broadband password provided by the operator, as shown in the following figure.

手机设置360家庭防火墙路由器上网3

If it is detected that the Internet access method is “DHCP”, there is no need to configure Internet access parameters, and you will directly enter the Wireless Settings (WiFi Settings) page.

If it is detected that the Internet access method is “static IP”, you need to fill in the IP address, subnet mask, default gateway, primary DNS, and backup DNS provided by the operator, as shown in the following figure.

手机设置360家庭防火墙路由器上网3-2

8. Set the wireless network name and wireless password, and click the “Save for Effective” button after completing it.

手机设置360家庭防火墙路由器上网4

9. At this point, the 360 router T2 is set up, the system will automatically restart, and some configuration parameters will appear on the page, as shown in the following figure.

手机设置360家庭防火墙路由器上网5

10. After the router is restarted, the mobile phone is connected to the newly set wifi signal, and you can surf the Internet after connecting.

手机连接新设置的wifi

Important:

After following the appeal steps, if your computer or mobile phone cannot access the Internet after being connected to the 360 router T2, it may be a wrong setting or a broadband failure. It is recommended to read the following article to see the solution.

What should I do if the 360 router T2 is connected to the Internet?

Post a reply

发表回复

您的电子邮箱地址不会被公开。 必填项已用 * 标注